The Best Places to Buy PCB And PCBA Assembly Service Online and In-Store

Just like the PCB business, our PCBA services also specialise in prototyping and small-volume production, making PCBWay the one-stop destination for board fabrication and assembly. This arrangement makes your R&D work easy and time-saving. Our professional engineers and technicians will work closely with you through our customer service people to ensure the best quality and quickest possible lead time. Fulfilling thousands of orders daily from around the world, we have established ourselves as the leading supplier of PCB and PCBA services for our consistent quality and excellent services.Our factory has self-developed the MES+ERP+IOT+ESD+APIS lean production management system. It is equipped with high-end equipment such as imported Fuji pick-and-place machines from Japan, 3D X-RAY, 3D SPI, self-developed MES, IQC incoming material inspection instruments, and intelligent first-piece inspection instruments. We are committed to providing high-quality small to medium batch production services.

If you are looking for more details, kindly visit our website.

PCBWay Assembly capabilities: SMT Assembly, BGA Assembly, Through-Hole Assembly, Mixed Assembly, Rigid Flex PCB Assembly Services, Electro Mechanical Assembly, Box Build Assembly, Product Assembly, Cable Assemblies. Compliant with a wide range of standards including IPC 610 Class 2 and Class 3.

Over the past two weekends or so, I&#;ve been cranking out Sir Box-a-Lot handhelds for family and friends. There is no way to make a project like this profitable, but the game is more fun than it might appear &#; and it&#;s cool to watch recipients&#; faces light up after receiving a homemade gift.

Sir Box-a-Lots, right off the garage production line.

Along the way, I ended up ordering the same printed circuit boards from several hobbyist-friendly vendors. Numerous comparisons of quality and cost for different PCB manufacturers can be found on the internet, but many of them are dated or suspect &#; so I figured it&#;s worthwhile to experiment and share my notes for .

OSH Park

OSH Park is by far the best-known hobby PCB source in the United States. They do not do in-house manufacturing; instead, they combine multiple small orders into a single panel, send this bulk order to a fabricator, then chop up the panel and ship your boards back to you.

The service is fairly expensive: a single Sir Box-a-Lot PCB (6.5×9 cm) costs about $15 shipped, and you need to order at least three. Rush orders are twice as much; a discounted bulk service brings the price down to $9 a board, but in that case, I&#;d need to order at least 20 PCBs. It is still cheaper than placing a low-volume order directly with a domestic manufacturer, but it adds a hefty price tag to some projects &#; and it&#;s a lot of money down the drain if you mess up the design.

On the flip side, the boards I received from OSH are best described as beautiful. Solder mask is robust and aligned perfectly. Gold-plated (ENIG) pads show no defects. Silkscreen text down to 0.6 mm (the &#;1&#; pin marker) is perfectly legible:

A close-up of 0.5 mm pitch TQFP-48 pads. FOV is around 15 mm.

Vias appear somewhat larger than specified in my Gerber files; I&#;d guess 0.5 mm instead of 0.4 mm. They are also minimally off-center &#; although not enough to cause any practical issues.

A subminiature speaker mounting area on the back of the board.

The overall appearance of the board is superb, with no dings, scrapes, or other defects in sight. The ordering experience was great too &#; down to the last-minute ability to upload revised Gerber files if you spot any errors down the line.

OSH Park board surface aspect.

DigiKey Red

DigiKey Red is a direct competitor to OSH. The service follows a similar business model of aggregating orders and then shipping them off to a PCB manufacturer; the manufacturer in question appears to be Royal Circuits in Hollister, CA.

The pricing is comparable to OSH: for Sir Box-a-Lot, it amounted to $14 per board with shipping, four boards minimum. In contrast to OSH, the boards are sent to you directly from the fabricator, but the service is actually slower than OSH &#; perhaps owing to lower order volumes. There is an expedited option costing twice as much, but no discount if you order more boards.

Compared to OSH, the ordering experience is considerably less polished. There are no updates along the way and no customer support to speak of; I tried to get in touch with a live person and had no luck. At some point, a package containing the boards, maybe with some rejects mixed in, will just show up in the mail. Perhaps in two weeks, perhaps a tad more.

Functionally, the quality of the boards is comparable to OSH. Once again, the solder mask is flawless, and so are the ENIG-finished pads. Vias appear even larger than on the OSH board &#; perhaps 0.6 mm instead of 0.4 mm? &#; but they are better centered, so I think I can let that slide.

TQFP-48 area, DigiKey Red.

Silkscreen is another matter. The text looks OK, but areas with long straight lines turned out to be a mess:

&#;Friday 4:55pm&#; silkscreen quality.

The cleanliness of the boards also left something to be desired: each and every one was covered in adhesive gunk, possibly from double-sided tape used for fixturing. Nothing here is a showstopper &#; but overall, I found the experience to be disappointing for the price.

JLCPCB

Additional resources:
New In Box ABB ACS550-01-180A-4 ACS55001180A4 ...

Shenzhen Thriver Digital Tech Co., Ltd. Product Page

JLCPCB is a Shenzhen-based manufacturer that caters directly to hobbyists &#; something too icky for the tastes of its US counterparts. The JLC model has two advantages. First, they offer a wide variety of process choices, whereas DKR and OSH are one-size-fits-all. Just as importantly, in-house manufacturing is faster than shipping boards back and forth: I ordered from JLC a couple of times, and every time, I received the boards within 7 days.

JLCPCB is remarkably inexpensive: a single Sir Box-a-Lot board costs about $1.50 to $2.00 shipped to your door if you order fifteen or so. And for the price, the quality is excellent, even if it doesn&#;t quite match OSH Park or DigiKey Red.

Here&#;s a close-up of a JLC board, showing well-aligned true-to-spec vias and HASL-finished pads with a tiny bit of JLC-added solder mask setback. The silkscreen is competent, but loses legibility below 1 mm:

Compared to the other two vendors, JLC solder mask layer is thinner and more fragile, and it&#;s the weakest aspect of the boards. It can be scraped off fairly easily and will come off if you keep reworking the same pad; in fact, one or two boards came with small scrapes from the factory. The mask still does what it&#;s supposed to do, but if you&#;re designing a device meant to be used without an enclosure, you should expect the mask to quickly acquire some wear and tear. Conformal coating might help.

Speaker mounting area.

My board design had a couple of mechanical holes with zero-clearance annular copper rings. As seen above, JLC added setbacks on the annular rings, leaving little metal in place; both DKR and OSH plated the holes instead. It doesn&#;t matter in this particular case, but it&#;s a good reminder to avoid ambiguity in one&#;s designs.

PCBWay

China-based vendors are plentiful, but few come close to JLCPCB in terms of speed, pricing, and consistent quality. A noteworthy contender is PCBWay. The company offers some added manufacturing capabilities &#; such as blind vias and buried passive components &#; but they charge a bit more and can take a bit longer to ship the merchandise; for a small Sir Box-a-Lot order, courier shipping would have resulted in a total of about $3-$4 per board.

I did not order the same layout from them, but a bit later, I gave them a try with a revised design featuring an SSOP-28 chip with 0.65 mm lead pitch. Here&#;s the result:

PCBWay board close-up, SSOP-28 area.

My overall impressions are positive. Silkscreen quality is about the same as with JLCPCB: not exceptional but perfectly adequate. The cosmetic appearance is excellent and consistent across all boards, with no scratches, dings, or dirt. The only real negative is that solder mask alignment is noticeably worse than for other vendors, with a fairly pronounced horizontal offset seen around the IC pads. On the flip side, the mask is considerably thicker than for JLCPCB &#; to the point of plugging some of the vias &#; so it is likely to take more abuse. Both Chinese vendors manufactured all vias true-to-spec and centered them well.

To their credit, PCBWay was the only company to contact me and ask what I wanted to do with the badly-specified non-plated through holes in my design; as discussed earlier, other shops made that decision on my behalf, with unpredictable results.

Perhaps of note: after I placed my order, PCBWay did a bit of sleuthing and then contacted me asking if I&#;d like to to get free prototyping in exchange for &#;slight promotion&#; on my blog. I did not take them up on that offer, but I imagine that many others would &#; and there can be some resulting bias in the reviews you see elsewhere.

Other choices in the US and abroad

In the States, your options are limited: although you can work directly with a manufacturer, you should expect to pay $350 or so for a couple of boards &#; or in excess of $1,000 if you need the PCBs soon.

There is a handful of other choices in allied countries, and on that front, Germany-based Aisler is of special note. Their pricing is higher than for China-based manufacturers, but the company still charges a lot less than OSH Park and DigiKey Red. The quote for twenty Sir Box-a-lot boards came out to $4.50 a piece.

I did not include them in my initial roundup, but I placed an order with Aisler in September for a slightly different board. Compared to the earlier samples, the most significant difference is the use of copper fill zones in between the traces. I should have cleaned up some of the unconnected copper islands visible in this photo, but bear with me for now:

The package arrived at my doorstep in around 20 days; it traveled via DHL from the factory to the airport in Germany, but then continued via USPS at a snail&#;s pace all the way from New York to the Pacific Northwest. Both JLC and PCBWay also use DHL, but they pay for the company to deliver in the US. This results in much shorter transit times for a comparable price.

When I opened up the envelope, the most noticeable difference was a distinctive, muddy-green solder mask with copper partly showing through and imparting a brownish hue here and there. This is OK for utilitarian PCBs installed in opaque enclosures, but falls short of the attractive, bright colors used by all the other companies covered in this article. The mask appeared thick, but in an unscientific &#;poke it with a hot soldering iron&#; test, it felt less scratch-resistant than the boards from OSH Park.

On most other fronts, the quality appeared to be roughly halfway between the Chinese vendors and the US-based ones. Silkscreen was solid, but not as crisp as for the first two companies covered here. Solder mask alignment near the LQFP-64 pads was very slightly off to the right &#; although not nearly as much as in the case of PCBWay. Via sizes appeared true to spec, but the holes were vertically off-center by a good amount.

Overall, I think that Aisler is a solid compromise choice if you don&#;t want to patronize the Chinese regime. If the company improves their shipping options to the US, I can see myself doing more business with them down the line.

If you liked this article, please subscribe! Unlike most other social media, Substack is not a walled garden and not an addictive doomscrolling experience. It&#;s just a way to stay in touch with the writers you like.

For advice on designing your own PCBs, click here. A list of other electronics-related articles on this blog can be found here.

The company is the world’s best PCB And PCBA Assembly Service supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.